Cisco Show Stacks Command

Unlock Best Pricing with In-stock, Ready-to-Ship Products

Show stacks is an exec command that is commonly used to diagnose system crash situations. The first section of this command’s output displays stack utilization of processes and interrupt routines, and the reason for the last system reboot. When a system crash happens, failure type, failure program counter (PC), address (operand address), and a stack trace are saved by the ROM Monitor. The show stacks command displays the data saved by the ROM Monitor. The stack trace is displayed in the second section of the show stacks command output (if there has been a system failure).

In the past, support engineers would submit the stack trace of their router to Cisco System’s technical support representatives, who had access to symbol tables, object files, source code, and the stack decoder software. And now, the stack decoder is available online (from the CCO) and you can cut your router’s stack trace from the output of the show stacks command and paste it in the input field of the stack decoder software. Stack decoder decodes the stack trace and creates a symbol file. The symbol file (perhaps along with other information in the trace) usually provides enough information to isolate the cause of any problems that were experienced.

The following example shows an example of the show stacks output from a bus error. The message “System was restarted by bus error” indicates that the processor tried to use a device or a memory location that either did not exist or did not respond properly (this could be due to a software bug or a hardware problem). Operand address, the address the processor was trying to access when the system crashed, is used as the clue to tell if the failure was due to software or hardware. If the operand address (reported on the output of the show stacks command) is valid, the problem is probably in the hardware. In other words, the operand address, not the program counter, provides the memory map location of the error, which can be used to infer the general area of the router where the error occurred.

Example: A Sample Output of the show stacks Command

Router# show stacks
 
Minimum process stacks:
Free/Size Name
652/1000 Router Init
726/1000 Init
744/1000 BGP Open
686/1200 Virtual Exec
Interrupt Level stacks:
Level Called Free/Size Name
1 0 1000/1000 env-flash
3 738 900/1000 Multiport Communications Interfaces
5 178 970/1000 Console UART
System was restarted by bus error at PC 0xAD1F4, address 0xD0D0D1A
GS Software (GS3), Version 10.2
Compiled Tue 11-Aug-94 13:27 by jthomas
Stack trace from system failure:
FP: 0x29C158, RA: 0xACFD4
FP: 0x29C184, RA: 0xAD20C
FP: 0x29C1B0, RA: 0xACFD4
FP: 0x29C1DC, RA: 0xAD304
FP: 0x29C1F8, RA: 0xAF774
FP: 0x29C214, RA: 0xAF83E
FP: 0x29C228, RA: 0x3E0CA
FP: 0x29C244, RA: 0x3BD3C

Failure types are usually one of the following: bus error, address error, watchdog timeout, parity error, or emulator trap. Table displays common failure types with a brief description for each of them.

Table: Common Failure Types Reported by the show stacks Command

Failure Type Description
Bus error The processor tried to use a device or a memory location that either did not exist or did not respond properly (could be due to software bug or hardware error).
Address error

(software forced crash)

The software tried to access data on incorrectly aligned boundaries (usually indicates a software bug).
Watchdog timeout Watchdog timer was not reset and caused a trap. Watchdog timers are used by Cisco processors to prevent certain system hangs (indicates a hardware or software bug).
Parity error Internal hardware checks have failed (this is due to hardware problems).
Emulator trap Processor executed an illegal instruction (illegal branching). A hardware problem, such as ROM failure, can also cause an emulator trap error.

This guide from ciscopress.com

Note: This guide from CCNP Support Exam Certification Guide introduces some powerful troubleshooting tools that are built into the Cisco IOS. As with other tools, it is important that you identify when to use them and what information they reveal. Because some of these tools have an impact on the way routers operate and may impede the routers’ utmost performance, it is essential to use them with care. To better understand the output of these commands, and to recognize what router internal operations they affect, this chapter discusses router internal components and operations. As each tool/command is introduced, its usefulness is described and tips are given on how to use it effectively.

Full Introduction of the book “CCNP Support Exam Certification Guide” you can visit: https://www.ciscopress.com/store/ccnp-support-exam-certification-guide-9780735709959?w_ptgrevartcl=Applying+Cisco+Troubleshooting+Tools_24109

More Cisco CCNP and CCIE Tips:

Top 10 Commands Every Cisco IOS User Should Know

Top 10 Cisco IOS Configuration Mistakes

CCNP SWITCH 642-813 Guide: Configuring IP SLA

Share This Post

Post Comment