Preface: Cisco 2500 Series Wireless Controller support a maximum of 50 lightweight APs in increments of 5 APs with a minimum of 5 APs, making it a cost-effective solution for retail and small and medium-sized businesses. The Cisco 2500 Series Wireless Controller offers robust coverage with 802.11a/b/g or delivers unprecedented reliability using 802.11n and Cisco Next-Generation Wireless Solutions and Cisco Enterprise Wireless Mesh.
Here I would like to share my experience of WLC Configuration to Different Aps Regions.
I have a Cisco 2504 WLC running Software Version 7.4.110.0 and I have 3 AIR-CAP1602I-C-K9s setup on it. Here I also checked the AP image to WLC 2504 and have log as follows:
Primary AP Image Size
—————- —-
ap1g2 9568
ap3g1 11288
ap3g2 11196
ap801 7164
ap802 8568
c1130 5072
c1140 9416
c1250 6944
c1520 8044
c602i 3736
Secondary AP ImageSize
—————— —-
ap3g1 5792
ap801 5192
ap802 5232
c1100 3084
c1130 4964
c1140 4992
c1200 3364
c1240 4812
c1250 5504
c1310 3136
c1520 6404
c3201 4324
c602i 3716
I got that the c602i is the AP image I need for my APs. But the problem is the WLC cannot find the APs, so I read Log from AP details below:
13 12:44:26.607: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(UNKNOWN_MESSAGE_TYPE (5)
*Nov 13 12:44:26.607: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Nov 13 12:44:26.607: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.30:5246
*Nov 13 12:44:26.651: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Nov 13 12:44:26.671: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Nov 13 12:44:26.671: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Nov 13 12:44:26.687: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Nov 13 12:44:26.719: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Nov 13 12:44:27.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Nov 13 12:44:27.719: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Nov 13 12:44:27.727: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Nov 13 12:44:28.711: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Nov 13 12:44:28.719: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Nov 13 12:44:28.763: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Nov 13 12:44:28.771: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Nov 13 12:44:28.779: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Nov 13 12:44:29.763: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Nov 13 12:44:29.771: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Nov 13 12:44:29.807: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Nov 13 12:44:30.807: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Nov 13 12:44:42.719: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Nov 13 12:44:42.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.30 peer_port: 5246
*Nov 13 12:44:42.507: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.30 peer_port: 5246
*Nov 13 12:44:42.507: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.30
*Nov 13 12:44:42.511: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Nov 13 12:44:42.511: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Nov 13 12:44:42.511: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Nov 13 12:44:42.511: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 192.168.1.30
In fact, it took me much time to solve this problem, I finally realized that Cisco has configured a country code ensures that each radio’s broadcast frequency bands, interfaces, channels and transmit power levels are compliant with country-specific regulations. Well, I changed the country code of my WLC and last it worked.
How to change the country code of a WLC? Before you can change the country code of a WLC, you must disable the 802.11a and 802.11b network:
>config 802.11a disable network
>config 802.11b disable network
Now you can change the country code of the controller. For example, we change it from US to CN (CHINA)
>config country CN
After changing the country, enable the 802.11 interfaces.
>config 802.11a enable network
>config 802.11b enable network
Change the Timezone if necessary on WLC:
(Cisco Controller) >config time timezone 2 0
And now we’ve got the right time :
(Cisco Controller) >show time
Time……………………………………… Thu Nov 17 16:50:17 2013
Change time on AP:
clock set hh:mm:ssday month year
More Cisco Networking Guide and Tips:
How to Use IP SLA to Change Routing?
