This article focus on the ways how we can secure SNMP access in Cisco Switches and Routers Simple Network Management Protocol (SNMP) uses the default UDP port 161 for general SNMP messages and UDP port 162 for SNMP trap messages.
SNMP is a service used to perform network management functions using a data structure called a Management Information Base (MIB). Unfortunately, SNMP version 1 is widely implemented but not very secure, using only clear-text community strings for access to information on the switch, including its configuration file.
If SNMP is not being used, then executing the following commands will disable the service.
Switch(config)# no snmp-server community
Switch(config)# no snmp-server enable traps
Switch(config)# no snmp-server system-shutdown
Switch(config)# no snmp-server
If SNMP is required for a switch or router configure the switch or router for SNMP version 3. This version is more secure than SNMP version 1 because version 3 can use cryptographic hashes for authentication to protect the community string. The above commands for disabling SNMP are recommended for use before deploying SNMP version 3 to remove any possible default community strings. The following commands show an example User Security Model for SNMP version 3 for the switch. The model begins with creating a standard access-list (e.g., 12) that allows only those systems that manage the switch. Next, define a group (e.g., admins) with read and write MIB views (e.g., adminview). Then each user (e.g., root) is added to the group with a password (e.g., 5ecret-5TR1N) that can be hashed (e.g., using md5) before being sent across the network. Also, the standard access-list (e.g., 12) is applied to the user. Finally, the MIB view (e.g., adminview) is defined by one or more statements to include or to exclude portions of the MIB.
The MIB view in the following example gives access to the Internet branch of the MIB except the branches that display IP addresses and IP routing information.
Switch(config)# no access-list 12
Switch(config)# access-list 12 permit 10.0.0.2
Switch(config)# access-list 12 permit 10.0.0.4
Switch(config)# snmp-server group admins v3 auth read adminview write adminview
Switch(config)# snmp-server user root admins v3 auth md5 5ecret-5TR1N access 12Switch(config)# snmp-server view adminview internet included
Switch(config)# snmp-server view adminview ipAddrEntry excluded
Switch(config)# snmp-server view adminview ipRouteEntry excluded
If SNMP is required for a switch and only SNMP version 1 is available, then the following commands show an example of how to configure the switch with a community string (e.g., g00d-5tr1n9) that has read-only permissions and a standard access-list (e.g., 12) applied to it.
Switch(config)# no access-list 12
Switch(config)# access-list 12 permit 10.0.0.2
Switch(config)# access-list 12 permit 10.0.0.4
Switch(config)# snmp-server community g00d-5tr1n9 ro 12
In addition to the configuration of the SNMP service, SNMP Trap information can be sent to the systems that manage the switches. The following commands show an example of this configuration.
Switch(config)# snmp-server host 10.0.0.2 traps g00d-5tr1n9-2
Switch(config)# snmp-server host 10.0.0.4 traps g00d-5tr1n9-2
Switch(config)# snmp-server trap-source Loopback0
Switch(config)# snmp-server enable traps
—Guide from https://itknowledgeexchange.techtarget.com
More Related Networking Topics:
How to Configure SNMP on Cisco IOS-based Router/Switch?
The Way to Activate Your Cisco ASA 5500
Cisco 3750 Stacking Configuration
